Keep your propagation setup organised, stable, and easy to manage with this 3 pack of corm cup holders.
This bundle includes one short, one medium, and one tall holder, allowing you to create a tiered display for 15 corm cups.
Perfect for use in cabinets, acrylic display cases or any other planty set up you might have!
1 × Short Corm Cup Holder
1 × Medium Corm Cup Holder
1 × Tall Corm Cup Holder
Total capacity: 15 corm cups
Available with or without integrated label tabs, designed around Niimbot labels for easy identification.
Small propagation cups can be a little too easy to knock over, so I made these holders to fix that, these seat the corms nicely making it significantly harder to knock them over, all while organising and neatening up your corm cups!
Height: 57mm
Width: 297mm
Depth: 50mm
Height: 89mm
Width: 297mm
Depth: 50mm
Height: 121mm
Width: 297mm
Depth: 50mm
Individual holders are also available separately.
I designed these risers with the cases below in mind so they’re a perfect fit. These are available from Amazon but aren’t my own personal products. They’re not necessarily the best ones, just the ones that I have bought and use myself. These are a tight fit but I wanted to maximise the space and make them nice and snug so they’re secure.
All 3 tiers fit perfectly in the small “eYotto Acrylic Display case for collectibles” (30cm x 17.9cm x 24.6cm)
I also have a couple of larger acrylic display cases “Clear Acrylic Display Case 4 Tier with magnetic door” - These ones stand upright and with a shelf installed in the middle, can hold 2 sets of these corm cup risers, with also a little room spare at the front for either an extra one of the tiers or some corm riser pots so you can have the best of both worlds!
Small Acrylic display case
Assembly instructions to make using these risers easier and minimise the chance of scratching the acrylic panels.
Slot both side panels into the back panel, but switch the left and right sides so that the back shelf mounting point is actually at the front otherwise it interferes with the tall riser being at the back.
Lay the box on its back and insert the corm cup risers.
Install top and bottom panels
Lastly install the front door panel.
Larger Acrylic display case
Here you can follow the same general advice as for the small box but these are a tiny but wider making it easier to fit the risers in even once the display case is fully assembled.
Colours marked with ** are printed in PLA.
PLA offers the widest range of colours, best print quality and is more than suitable for the intended use of this product. While PLA is generally less resistant to prolonged heat and humidity than PETG, I have used PLA planters and self-watering outers in my grow tent that sits around 28°C and 80–95% humidity for over two years without any issue.
Colours without ** are printed in PETG.
PETG offers increased durability, better heat resistance, and improved long-term performance in demanding environments.
Both PLA and PETG are suitable for use in a corm cup, however if you prefer the most durable option with the best long-term performance then a PETG option should be chosen.
Please note: To ensure long-term durability, these inserts should be used under normal room temperature conditions. They are not designed for use with heat mats, germination mats, or other heated surfaces, as prolonged exposure to heat may cause slight warping.
Keep your propagation setup organised, stable, and easy to manage with this 3 pack of corm cup holders.
This bundle includes one short, one medium, and one tall holder, allowing you to create a tiered display for 15 corm cups.
Perfect for use in cabinets, acrylic display cases or any other planty set up you might have!
1 × Short Corm Cup Holder
1 × Medium Corm Cup Holder
1 × Tall Corm Cup Holder
Total capacity: 15 corm cups
Available with or without integrated label tabs, designed around Niimbot labels for easy identification.
Small propagation cups can be a little too easy to knock over, so I made these holders to fix that, these seat the corms nicely making it significantly harder to knock them over, all while organising and neatening up your corm cups!
Height: 57mm
Width: 297mm
Depth: 50mm
Height: 89mm
Width: 297mm
Depth: 50mm
Height: 121mm
Width: 297mm
Depth: 50mm
Individual holders are also available separately.
I designed these risers with the cases below in mind so they’re a perfect fit. These are available from Amazon but aren’t my own personal products. They’re not necessarily the best ones, just the ones that I have bought and use myself. These are a tight fit but I wanted to maximise the space and make them nice and snug so they’re secure.
All 3 tiers fit perfectly in the small “eYotto Acrylic Display case for collectibles” (30cm x 17.9cm x 24.6cm)
I also have a couple of larger acrylic display cases “Clear Acrylic Display Case 4 Tier with magnetic door” - These ones stand upright and with a shelf installed in the middle, can hold 2 sets of these corm cup risers, with also a little room spare at the front for either an extra one of the tiers or some corm riser pots so you can have the best of both worlds!
Small Acrylic display case
Assembly instructions to make using these risers easier and minimise the chance of scratching the acrylic panels.
Slot both side panels into the back panel, but switch the left and right sides so that the back shelf mounting point is actually at the front otherwise it interferes with the tall riser being at the back.
Lay the box on its back and insert the corm cup risers.
Install top and bottom panels
Lastly install the front door panel.
Larger Acrylic display case
Here you can follow the same general advice as for the small box but these are a tiny but wider making it easier to fit the risers in even once the display case is fully assembled.
Colours marked with ** are printed in PLA.
PLA offers the widest range of colours, best print quality and is more than suitable for the intended use of this product. While PLA is generally less resistant to prolonged heat and humidity than PETG, I have used PLA planters and self-watering outers in my grow tent that sits around 28°C and 80–95% humidity for over two years without any issue.
Colours without ** are printed in PETG.
PETG offers increased durability, better heat resistance, and improved long-term performance in demanding environments.
Both PLA and PETG are suitable for use in a corm cup, however if you prefer the most durable option with the best long-term performance then a PETG option should be chosen.
Please note: To ensure long-term durability, these inserts should be used under normal room temperature conditions. They are not designed for use with heat mats, germination mats, or other heated surfaces, as prolonged exposure to heat may cause slight warping.
